I made it home safe from Seattle and it’s right back to work! I mentioned earlier that I was staying with my cousin and helping her update her living room there. It was a pretty hectic week with both of us having to work and make a few last minute shopping trips in Seattle traffic, but we were able to accomplish a good amount and set aside time for some fun outings as well (more photos to come Friday!)
The project I am most proud of (and excited to share with you guys) is this sofa table I built:
I say proud because I figured out a way to build it using only a drill & screws (and a basic saw to cut a few small pieces of wood!) That means 95% of you can do this too. By yourself. In one day, for $30 or less.
Materials
- 2x2x8′ furring strips (qty 8)
- 2x12x10‘ (qty 1)
- Screws (2.5-3″ long)
- Wood glue
- Wood stain or paint
Tools
- Drill
- Saw (miter, chop saw or miter box)
- Kreg Jig (or simple brackets)
- Sand paper (or electric sander)
My cousin had a long sofa (just over 9 feet wide) and was using an end table that was blocking part of the walkway, so I thought the perfect solution would be a long narrow table behind the sofa for more convenient storage.
I was having trouble finding a simple plan I liked online, and knew this table definitely had to be customized so I decided to come up with my own. We were also working with a budget so I wanted to do this as inexpensively as possible.
I drew a quick sketch to illustrate my idea (excuse the roughness of it):
I was envisioning a very simple, modern style table constructed using 2×2’s and a 2×12″ for the top portion. The drawing isn’t super accurate as there should be 2×2’s horizontally at the top for reinforcement (below the 2×12) but you get the idea. I knew 2x2x8′ furring strips were under $2 each and the 2x12x10‘ was only around $12, making this project about as cheap as you can get for such a large table.
This can be done a lot simpler and for even less if you plan on making a shorter table by eliminating the middle piece. I put it in there for stability, but if the table was shorter than ~6 feet or so, I’d leave it out.
Here’s what we brought back from the hardware store—a 2x12x10′ and eight 2x2x8′s. Simple stuff.
My cousin had very limited, basic tools in her garage which proved to be a challenge but fortunately we were able to borrow a neighbor’s saw to make the smaller cuts, and we had the the 2×12 cut to 9′ for us.
You’ll end up with three different sizes—the long horizontal pieces, the vertical legs, and the shorter pieces to connect the legs (these will be different depending on the size of your table).
First it’s time to assemble the rectangles! I grabbed four pieces and arranged them:
You’ll need to drill pilot holes so the wood doesn’t split—that’s a very important step especially with this type of wood that splinters easily and since the pieces are so narrow. I was able to find 3 drill bits in the garage and luckily one of them ended up working. You want it to be just a bit smaller than the width your screw.
I bought 2.5″ screws for this project which worked fine but 3″ may have been even better. First I aligned my two pieces into place and drilled my pilot hole through both. I made sure to do this towards one end of the board instead of the center, since I would have to insert another screw in the same area for the horizontal pieces and there needed to be enough room for both screws to pass through without hitting each other.
Then I applied the glue onto the end of a short piece…
After setting it back into position, the first screw went in:
I did this on each end (3 more times) until my rectangle was built:
And then built the remaining two pieces. Step 1 complete!
This is where it gets a little trickier when you’re working by yourself. You have to start balancing things and holding them into position while attaching them together with glue and screws. I had no clamps or flat surface to work on, and the drill I was using didn’t have a lot of power, and the drill bits didn’t fit the screw heads perfectly so there was some frustration involved. If I can do it under these conditions, you definitely can too!
The next step is to attach the long horizontal pieces. I propped up my rectangle and got the pieces into place, then repeated the attachment process with my pilot hole, wood glue and screw. It seemed to work fine…
But when I lifted it up to flip it over and add the other two horizontal pieces, I found they were wobbly so I had to reinforce it with a second screw. One screw works fine for the smaller lengths of wood but just doesn’t cut it for the longer pieces. And I made sure to counter sink them so that a) they’d grab a little more of the wood and b) I could fill the holes so there weren’t any visible screws.
Two screws did the trick, and I then attached the second rectangle to the opposite end.
I flipped that piece over and attached the last two horizontal pieces the same way. If you were building a smaller table, this would be your last step before adding the top and it would be pretty much the easiest project ever.
But I had the dilemma of attaching a whole other section without a Kreg Jig or anything of the sort, so I ended up buying 2″ brackets:
This part was definitely the biggest challenge of the entire project. Even with two screws holding the longer pieces together, they’re quite long so they don’t stay perfectly straight and I had to hold everything into place while keeping them elevated and drilling pilot holes, applying glue, lining up the brackets and attaching the screws.
Somehow I made it all happen. Precise measurements and cutting is a crucial step, otherwise everything may not all fit together!
Also, these furring strips aren’t perfect, but luckily dark stain goes a looong way to hide imperfections. I didn’t even have wood filler so I used drywall mud + sawdust and you can’t tell at all with the finished product.
After the brackets went on and the base of the table was finished, it was a huge relief!
The next part was easy—add some wood glue to the top:
Then lift your 2×12″ into place.
And secure it with screws from underneath. I used 8 in total.
Then it was all about the finishing touches. There was no electric sander available so I picked up some 80 grit and went over each piece by hand. Labor of love, baby.
After it was all smooth and splinter-free, I applied a dark walnut stain which coordinates nicely with the warm woods in her home.
Finally, I brushed a shellac onto the top piece (for extra durability) and used a matte wax on the base since it’s easier/faster and that part doesn’t need the same level of protection as the top.
We hauled it upstairs to the living room and set it in place. And it’s perfect.
Her home is a split level so it’s one of the first things you see when you walk upstairs into the living room:
The back wall hides half of it, but it’s such a versatile piece that can be moved anywhere and travel to new homes in the future.
And they get a fun area to display pretty things.
I’m just a little bit jealous and know exactly what I’ll be making for myself the next time I need a table!
Now I’m passing on the challenge to you—if you have a way to cut wood and a drill, you can make it too!
This has to be one of my top 3 furniture builds ever and it was so rewarding to see how much my cousin loved it and how happy she is to have it in her home. And I hope this will inspire you to take action as well and try something new!
Hope you’re all enjoying the first official week of summer—make sure to keep up with everything that’s been going on over on instagram and I’ll be back Friday with more photos.
MikeinTexas says
Love the post and that it is so well detailed. My daughter has 9 foot couch and needed a table like yours however she was concerned that her small dog would get behind the couch. We used a 2 x12 top and also used 2 x 12s for the legs. Both were cut for us at home center. Used scrap to make large triangular braces and 1 x3s on sides of top to help keep it from sagging. We glued all joints and countersunk screws and filled them with water putty. Finished table was painted black. Your idea with a twist. Fabulous.
Heather B says
Hi there,
I am SO excited about trying this out. It’s exactly what I’ve been looking for! Mine won’t be going between a wall and the sofa, it’ll just be right behind the sofa to create a foyer space in a room that doesn’t have one. Did you find it to be pretty stable on it’s own (to set drinks or decorations on) if there was nothing behind it? Do you think there’d be any issue with it wobbling when people sit on the sofa? These are complaints that I’ve seen with other “skinny” sofa tables, so I was just checking first 🙂 Thanks! Love it , love it, love it!!
jennasuedesign says
Mine was pretty heavy and solid! I think it’d only be wobbly if the lower legs weren’t level and/or the floor was not even.
Caroline M says
Hello! Please let me know where this couch is from! I love the table and couch together!
jennasuedesign says
Hi Caroline, it’s from Ikea 🙂
Nathan Helzer says
Great looking table. What kind of wood did you use?
Ashlyn says
This is fabulous!!! Looks great!! https://www.lovesthefind.com/