The dresser is done!
So many of you have been following this project from the beginning on my Instagram stories, and now the wait is over. For those of you who are just joining, it all started with this inspiration…
I’ve been noticing this fluted/reeded furniture trend in high-end design for a while and I’m here for it. However, I’m not here for the insane price tag. Like $2700 for this dresser (I love you McGee and Co, but jeeeez!) and $1950 for this chest. These pieces are not out there in the mainstream market so they are ultra expensive and exclusive.
Jump to:
Until now…*dun dun dunnnnn*
On my latest quest to get the look for less, I went dresser hunting at my favorite place to shop: Facebook Marketplace, of course (you already know the deal if you’ve read this post). I was looking for a solid wood chest with full overlay flat drawer fronts, with the goal of recreating my inspiration photo:
Lucky for me (or thanks to my sleuth skills) this shabby little Ikea Tarva dresser popped up, and it was perfect in all its’ sloppily-stained glory:
The asking price was $40 but they accepted my offer of $30, and that afternoon Miss Tarva was home safe in my garage, ready for her Extreme Makeover. Here’s what you’ll need for this project:
Materials
- A dresser with a flat front
- Fluted trim
- Strong adhesive
- Caulk
- Paint
- Varnish
Tools
- Miter saw
- Table saw
- Drill
- Electric sander
- Clamps
- Velour roller (or sprayer)
- Paint brush (or sprayer)
I’ve been around a lot of trim in my day, and knew there was a variety of fluted trim that could create the look I was after. I reached out to my friends at Ekena Millwork (I use them for all my fancy trim projects) and requested three different products to try out:
Any of these could have worked, but the left was a little thicker than I wanted, and the smaller pattern on the middle was a bit too subtle. The right one seemed perfect!
The trim comes in 94.5″ lengths and each drawer required almost exactly one piece. Three pieces at $16/ea = $48 in materials, not too bad. A couple of you suggested using tambour panels (which is probably what furniture makers use) but they’re super expensive! If you know of an affordable source for these, please do share.
Step 1: Sand
This is my least favorite part of furniture refinishing, but an important step for best results. The furniture paint I’m using is technically “no-prep” which means no sanding, however paint always adheres better to bare wood, so I think it’s worth taking the extra time. I used 80 grit paper on my orbital sander and spent maybe 15-20 minutes roughing up the surface.
I didn’t need to eliminate the stain completely—just enough to remove the shiny varnish layer on the surface. If your piece is painted, you can use a paint stripper (I like Citristrip)… or just say screw it and paint right over with a good furniture paint. I did that with our living room buffet and powder bath vanity and they’ve held up well so far. Any experienced furniture refinishers care to weigh in on the best practices?
Step 2: Cut the trim
Next it’s time to start cutting. This measurement had to be precise—our drawer height was 9 7⁄8” (fortunately all three drawers were all the same!)
Most importantly, each piece had to be cut to exactly the same size. Here’s a neat trick to do this: make a stop block on your miter saw, using a scrap piece of wood and a clamp (the clamp came with our saw):
This eliminates the need to measure each time and will ensure they’re all exactly the same length—pretty cool, huh? It only took a few minutes to cut them all (each drawer required 10 cuts/1 full piece of trim).
Here’s how it looks from the side:
Step 3: Rip down the end piece
Chances are the last piece is not going to line up exactly with the edge of your drawer. In our case, it worked out surprisingly well with the edge of the drawer lining up with the last groove:
To get a nice even cut, we ran it through our table saw…
And voila!
Step 4: Glue and clamp the trim
Now we’re getting to the fun part. Because this trim is made of urethane (essentially hardened foam) it’s super lightweight and can be glued on—no nails required! You should be able to use any heavy duty glue, and we opted for Liquid Nails since we always have it on hand:
We applied it generously to make sure the trim wouldn’t ever budge, and lined each piece up one at a time.
Liquid nails takes hours to harden completely, so you can go back and make adjustments after getting everything in place.
We cut a piece of scrap plywood to clamp everything down securely without damaging the trim, and bought this pack of spring clamps in advance, knowing we’d need a lot for this project.
The plywood helped to keep everything in place, but the edges of the trim were still lifting up a bit so we had to use small clamps directly on all of the problem areas. We ended up running out of clamps and had to get creative with whatever tools we had on hand…
I realized later that chip clips would also be a good solution!
If you do this project, make sure to have enough clamps for each piece of trim just in case. If the trim doesn’t line up evenly, it will be noticeable in the end.
While the trim was drying, we flipped the dresser upside down to remove the legs. This part is completely optional, but I wanted to be able to use this as a night stand, and it was too tall with the legs (36″).
Fortunately, the legs were attached with brackets and easily removable. We picked up a set of these nail-on furniture glides to protect the bottom of the dresser and the floor:
You simply drill a small pilot hole then nail them in. Easy peasy!
Then it was time to address the hardware. A reader pointed out that these are actually not the original Tarva knobs (which are wood) but these $1 knobs from Home Depot. I liked them, but wanted gold instead of black.
Simple fix: I gave them a quick makeover using my Rub n Buff technique in European Gold (I didn’t spray paint them first since they were already black, we’ll see how they hold up…)
If you have the original wood Tarva knobs, you can use this same technique! Just make sure to spray paint them black first (check out my Rub n buff tutorial above).
Step 5: Drill hardware holes
We let the liquid nails dry overnight, then drilled through the existing hardware holes from the inside of each drawer. The problem was, the knob was hitting the drawer at an angle…
That wasn’t going to work, so we used a large drill bit the same size as the knob to bore out a hole:
We drilled through just enough until there was a flat surface for the knob to sit against:
Step 6: Sand/clean the drawer fronts
On the right edge of each drawer, there was a small ridge where the table saw cut the trim. I wanted this edge to be rounded to match the left side, so I gave it a quick pass by hand with 120 grit paper:
And then a 220 sanding sponge to smooth it down nicely. Here’s how it looks before and after:
You can also take this time to sand down any imperfections you find on the surface. Make sure to thoroughly clean off all the dust before the next step, either with a dry paint brush or an air gun:
Step 7: Caulk the seams
There’s a noticeable seam where the trim pieces meet:
Paint alone won’t fill this in, so you’ll need to run a bead of caulk down the groove. I do it the good old fashioned way with my finger and a wet sponge:
Magic!
Heads up: if you want the seams to be completely undetectable, make sure to fill them so they match the other grooves exactly. My grooves were a bit deeper because I didn’t use enough caulk, and it was noticeable after painting. It doesn’t really bother me—it looks like it was on purpose because the pattern is uniform (it kinda resembles my inspiration photo) but it’s pretty tough to get every seam to match exactly. If you try it, let me know!
Once the caulk is completely dry (I’d give it at least a few hours to be safe, even the fast-drying caulk) it’s time to paint!
Step 8: Paint
There’s all kinds of products you can use and techniques to do these next steps, so don’t feel like you have to follow my steps exactly. I use Maison Blanche specialty furniture paints because I love the result, I always have their paint on hand and I’m an affiliate. I don’t use regular latex paint for these types of projects and would recommend a paint made for furniture (any chalk paint) or specialty paint made for cabinets (like SW Emerald or BM Advance). I don’t have experience with any other chalk paints so I can’t give a different recommendation, unfortunately. If anyone else has a furniture paint they love, please share so I can pass the info along!
Tip: for a clean paint line, use painter’s tape along the inside edges of the drawers:
For this project, I use Maison Blanche in Wrought Iron (which I end up using for 3 out of 4 furniture projects, I’m addicted!)
I used a foam roller for a smooth and even application on the flat surfaces, like the dresser frame:
And my favorite angled paint brush on the drawer fronts. Smooth, even coats are key:
Coat 1:
The wood dresser soaked the paint right up and provided full coverage after 2 coats, but the coated urethane trim needed a few coats. Here’s after one coat on the left and two on the right:
I thought two coats was all it needed, but when I came back the next morning I noticed a few light areas peeking through:
Here’s how two coats look after drying on the wood (so rich!)
The paint dries fast, but you’re supposed to wait at least 24 hours until applying varnish, so I waited patiently while they dried in the garage…
Step 9: Varnish
This is another step that you can do many different ways. I stick to brush-on water based varnish since that’s what I have experience with, but if you have suggestions for something else to try, I’m all ears!
For this project, I used Minwax Polycrylic sealer in satin. Normally I love the matte look on furniture, but for this dresser I wanted a slight sheen:
Before applying, I lightly sanded the dresser frame with my 220 sanding sponge to make the surface as smooth as possible. One reason chalk paint is preferred for furniture is because it offers a velvety smooth finish after sanding, something a latex paint can’t replicate.
I could have sanded the drawers to get the same finish, but the paint was pretty smooth already and I didn’t think it would make a noticeable difference after varnishing. Totally up to you! Here’s the full instructions on the can:
After wiping the dresser down, the first coat went on nice and smooth with my foam roller (it goes on cloudy and dries clear):
After drying:
On the second coat, the air bubbles didn’t evaporate fully and I had to brush them out (I think the wood just absorbed them on the first coat). I then remembered having the same experience with a foam roller and varnish years ago, so for the third coat I stuck with my brush, which worked just as well. Skip the foam roller! Tip: an experienced reader told me she uses velour mini rollers from Sherwin Williams, which provide a smooth bubble-free finish. Give those a try!
Varnish not only protects the finish, it also deepens the paint color. The top drawer is before varnish and the bottom is after (one coat, still wet):
The most IMPORTANT advice I can give you: be careful of drips! They pop up everywhere, even after you think you got them all…
These will dry cloudy white and you can’t sand them down easily, and they start to harden in minutes. These drips are a refinisher’s biggest enemy! Unfortunately, I missed a few…
I’m going to have to touch up these spots with paint and re-varnish them. Sneaky little buggers!
I gave everything three coats of varnish (waiting 2 hours and lightly sanding in between each coat, except on the drawers) and added a fourth coat only on the top of the dresser since that gets the most wear and tear. Even though the varnish is fully dry and ready to handle in 1-2 days, I find that it becomes more durable over time, and try to wait at least 1-2 weeks before regular use (like setting heavy objects on it). Maybe it’s in my head, but that has been my experience. Anyone else?
Okay, who is ready to see this finished fluted dresser already?! Here she is…
How about a comparison with my $2,109 inspo:
I like mine just as much 🙂
After four days of work (well, really only maybe five hours of actual “work”… the rest was waiting) I feel like I created and birthed this baby from my own body.
So yes, I’m a little attached… but I have to set this baby free. This was a #furnitureflipfriday project and soon she’ll be for sale.
Now the question is… what is she worth? The dresser cost me $30, the trim was $48 (it was sponsored but I’m including it in the cost to be realistic) and $4 for the drawer glides. The paint and varnish I already had on hand. An $82 investment plus 5-ish hours over a weekend project—what do you think?
It is still an Ikea dresser under the façade, and the bottom two drawers don’t glide as smoothly as they should.
But it sure is one of a kind! And it totally matches Susie ?
If you decide to try this at home, I’d highly recommend tracking down an Ikea Tarva dresser for these reasons:
- It’s solid wood
- It has full overlay drawers with an overhang at the top
- It’s mass produced and should be easy to find online secondhand inexpensively (patience!)
- The feet are removable so it can work as a dresser or night stand
- The width is ideal for this fluted trim (if you use the same kind)
- The drawers are all the same size so it makes cutting easier
- You can use the existing hardware (Rub n Buff makeover!)
You can bet I’ll be keeping my eye out for more of these dressers on FB marketplace to do it again. It makes for an enjoyable and easy weekend project (the worst part was sanding, which isn’t that bad). If you make one, please let me know! I’d love to show it off (don’t forget to pin this tutorial for later!)
If you like this project, check out these popular Ikea hacks from my Project Library!
- Built-in custom Pax wardrobes
- The ultimate Ikea Dream Closet
- Custom Ikea Pax Pantry
- Painted Ikea Kitchen
- Custom Ikea office built-ins
Carla from Kansas says
It looks great but won’t dust collect in every one of those indents?
Jenna Sue says
Not any more than any other trim in the house 🙂 It’s a very quick clean with a dust pan or vacuum + brush attachment.
janice kirwan says
Very nice job! I’ll be on the lookout for something to use these moldings. I have tried the polycrylic spray …comes in matte and satin for those surfaces that have alot of detail. It dries great, no bubbles and nice smooth finish. I think you could get $250. Good luck!
Jenna Sue says
Thanks Janice! I’ll have to check that out.
Teri says
Using those hammers – genius and totally thinking out of the box which is what you do so well! Thanks for sharing this make over, I can’t believe you’re not keeping it! Will you share what you sell it for?
Jenna Sue says
Thanks Teri! And you bet I’ll be sharing on my next Furniture Flip Friday post 😉
Karen says
You’ve done itagain. Blown it out of The park! Tell us please , what you end up getting for it. I was so disappointed that it would be for sale. Guess you can always flip another one.
Ivory says
Wow, I love this spectacular job you did. I am so in love with the results, which looks likes it’s worth a million dollars. Thanks for sharing.
Ami says
Wow. You really nailed it. I bet it looks even better in person. Just a quick FYI. If what you mean by hardware on the Tarva dresser is the knobs, those knobs are not original to the piece. I had to smile when I saw them because I have used them countless times on furniture flips I’ve done. They are cute, cheap and really easy to change up with paint or rub and buff. Warning, rub and buff does eventually “rub” off. Learned that the hard way. So hope that helps you and your readers out. Knobs are Home Depot. I can send the link if you’d like.
Jenna Sue says
Oh shoot, no kidding! Thanks for the heads up Ami, I’ll update the post now! I just found an original Tarva dresser and it looks like the knobs are wood, but similar shape/size. You could definitely keep those and rub n buff them, I bet the gold would stick to the wood better (I’ve done that with wood knobs and they’re still going strong). I might just spray paint the knobs and redo the gold now to be safe since it seems to stick pretty well to that.
Monica says
Wow – this looks just as good as the high end pieces!
Deborah Hutton says
Oh my goodness! Susie and that dresser are twins separated at birth! Even their eyes match. Both are lovely, but Susie is extraordinary. Don’t sell HER on Marketplace lol.
Jenna Sue says
Lol isn’t that a coincidence 😉 Susie is priceless!
Ice Cream & Tequila says
Looks beautiful! Have you flipped other Ikea furniture that’s not made from wood? I think my kitchen table from Ikea is particle board.
Nita says
I rub paraffin wax on the underside of the drawer and inside the runners or meeting parts of the dresser. The drawer will then slide smoothly. Paraffin also works great on curtain rods to help drape rings slide smoothly.
Jenna Sue says
Thank Nita! Unfortunately for this dresser, it’s slightly just too narrow at the bottom so the track can’t roll freely. Not sure if we can fix that…
Alix says
You are amazing! I love your simple steps and will totally be doing this! Thanks for the inspiration and the encouragement of being able to do these things ourselves. It’s very empowering and you’re super smart!! You are a designer I love to follow and have given me great ideas over the years. So thanks!
Jenna Sue says
That’s so sweet of you to say, thank you Alix!
Jo says
Where did you get that cute concrete plant pot?
Jenna Sue says
It’s a DIY! https://www.jennasuedesign.com/2020/04/diy-hypertufa-stone-planter/
Chelsea Jo says
Absolutely gorgeous! Love following along with this! Thank you!!
Ali S. says
Love this so much! I have been thinking about painting/updating my two bedroom nightstands and this seems pretty doable. I can’t believe you are selling it. I really think it came out to look very high end. Thanks for the easy steps too!
Katie says
Hi Jenna! The dresser looks amazing! I’m a new follower and obsessed with your furniture flips. I plan to flip a few dressers over the next few weekends and would love to use Maison Blanche in Wrought Iron but it’s sold out
Any dupes or similar colors in available paints like SW or BM? Thanks in advance! Xx
Jenna Sue says
Hi Katie! Any black chalk paint should work. I asked the owner at Maison Blanche about restocking, and she said they should be back in stock in 10 days if you wanted to wait 😉 If you want to go the latex paint route, SW Tricorn Black is the deepest/richest black.